Up Suntubes Low Profile Parts and Components

Parts and Components
 

 

 Up

 

On this page you will find a listing and description of almost every major part available.  The listing starts at the top dome and goes down.

You shouldn't ever need to replace anything but it is possible that parts get lost or destroyed.

Distributors typically have most of these parts on hand.

ODL Items (available for both sizes)

Item

Description / Use

Top Dome Standard replacement dome
Top Dome Hurricane Tested More for stones and branches in Canada
Top Elbow Now separate parts for tighter fit.  Also 25" long
Bottom Elbow
20" Pipe Section  
48" Pipe Section  
Ceiling Diffuser:
   Insulated tempered glass
New kits include this as standard equipment.  Complete with ceiling clamp assembly, trim ring and double glaze flat diffuser
Ceiling Diffuser:
   Deluxe Frosted glass dome
An exquisite upgrade to the standard kit.  Not as bright directly below but more dispersal throughout room
Light Kit Not available in Canada.  110 volt light should not be used inside any suntube.
Low voltage kit available special order or source your own at a building centre
Iris Available special order only.
Low voltage motor with wireless remote.  Requires access to 110 volt source in attic
Hardware  
   

SunScope Items

Item

Description / Use

For Sizes
Top Dome - Acrylic Crystal clear high grade dome allowing maximum light transfer. All
Top Dome - Lexan As above: Lexan for special apps. 13,21
*Top Dome Seal Breathable seal between top dome and top tube section All
SunScoop Large reflector aimed south to capture the maximum light. All
Retention Clamp Stainless Steel clamp to hold top dome and SunScoop to tube. All
Storm Collar Cone shaped metal ring to give added weather protection. All
2' Light Tube Aluminum tube with highly reflective plating giving near perfect light transfer.

Mechanical connection for all joins

All
3' Light Tube 13,15,
4' Light Tube 8 1/2 13,15,21
Standard Flashing Metal fixture forming weather seal attached to roof with light tube passing through.  Suitable for asphalt shingle roofs between 2/12 and 9/12 All
Flat Roof Flashing Heavy grade metal flashing w/ soldered connections suitable for melting into flat or nearly flat roofs.  Submersible. All
Steep Roof Flashing As standard but for 10/12 - 12/12 All
*Metal Tape Heavy metal adhesive used as a secondary seal between tube sections. All
Elbow 3 piece swivel; adjustable from 0 - 45 degrees.  Used to allow light tube to pass around obstacles or to accommodate non horizontal ceilings.  Never use directly above ceiling or performance will be reduced. All
Iris Allows light to be blocked or dimmed without interfering with light transfer when open 13 or custom
Light Kit CSA approved low voltage halogen
Installs above diffuser.  50 watt
All
Flange Ring Metal ring used in rooms with  suspended or no ceilings.  Attaches to tube and diffuser attaches to it. 8.5,13,15,21
Interior gasket Forms seal between diffuser and ceiling.  Prevents air transfer between tube and room thus eliminating condensation in tube All
Standard Interior Dome Ceiling fixture acts as light diffuser.  Slightly white and deep to properly diffuse light in room All
Lexan Interior Dome As above in Lexan 13,21
Oval Interior diffuser dome- 5/12 Used to allow light tube to enter room at almost any angle.  Eliminates the need for an elbow.  Round dome will accommodate small oval entry. 13 only
Oval Interior diffuser dome- 9/12
Oval Interior diffuser dome12/12
Decorator Ring Distinctive white ring covering edge of diffuser dome.  Screw-less attachment. 13,15,21
Hardware Pack (includes *) Includes all needed small parts excluding roofing nails / screws All
Installation Video 21 minute complement to the installation instructions. All, 15" different
Demonstration Video 3 1/2 minute presentation of product All

   

Copyright 2006 Lynch Suntubes. All rights reserved.


Contact Us.
Last modified: 09/08/06                     Site hosted by  www.dotcanada.com